MicroCraft

  • On-demand InkJet Printing System

Equipped with one high-definition print heads.

C1D model

C1D

High-Definition Printing Model
C1D6151 / C1D7861
Equipped with one FUJIFILM Dimatix print head with 2048 nozzles, 2.4pl minimum droplet volume, and 100kHz maximum discharge frequency.

Detailed Specification

C1D6151 C1D7861
Max. Panel Size

24.6 x 21” (625 x 535 mm)

31.3 x 25.6” (795 x 651 mm)
Max. Discharge Frequency

100 kHz

100 kHz
X-axis Resolution (dpi)

1200 / 2400 / 3600

1200 / 2400 / 3600
Y-axis Resolution (dpi)

600 / 1200 / 2400 / 3600

600 / 1200 / 2400 / 3600
Min. Droplet Size

2.4 pl

2.4 pl
Number of Nozzles

1 x 2048

1 x 2048
Standard Resolution

1200 dpi

1200 dpi
Min. Line Width *1

40 µm–60 µm

40 µm–60 µm
Speed *2

22.8x17” (580 x 430 mm): 27 seconds

24 x 20” (610 x 510 mm): 32 seconds

22.8x17” (580 x 430 mm): 27 seconds

24 x 20” (610 x 510 mm): 32 seconds

30.7 x 24” (780 x 610 mm): 46 seconds
Number of Ink Tank

1

1
Ink Tank Volume (Max.)

300 ml

300 ml
On-Head UV Lamp *3

LED-UV lamp

LED-UV lamp
Number of Alignment Cameras

1

1
Camera Resolution

0.44 x 0.33” (11.2 x 8.4 mm)

0.44 x 0.33” (11.2 x 8.4 mm)
Air Supply: Pressure

0.5 MPa

0.5 MPa
Air Supply: Volumetric flow rate

2.7 ft³/min. (75 ℓ/min.)

2.7 ft³/min. (75 ℓ/min.)
Power Supply *4
Single Phase AC200–240 V 50/60 Hz

20 A

20 A
Weight

1984 lbs. (900 kg)

2646 lbs. (1200 kg)
Dimensions [ unit: inch(mm) ]

Operating Conditions 70–75°F (21–24°C), 30–70% relative humidity
* Free of moisture, dust (ISO class 7 (FED-STD-209D Class10,000) clean room or better), vibration, and corrosive gas.
Atmospheric Dew Point: −14°C or below (at 0.7 Mpa, dew point is 15°C or below)
Oil Mist Concentration: 1 mg/㎥ (ANR) or below

*1 Depends on ink *2 While using UV pinning type ink, speed spec may change according to required UV energy. Print times do not include image alignment, shuttle and load and unload time. Please confirm the printing quality and speed by allowing us to run a benchmark test at MicroCraft. *3 LED UV lamp to be mounted depends on the ink to be used. *4 Separate power source for cooling device and vacuum pump is necessary (specifications may be different in some countries). § Replacement of ink requires special training § CraftPix consumables are ink, cleaning fluid, filter, sending fluid tube, UV lamp, array unit, vacuum paper, temperature sensor, heater, etc. § Please contact MicroCraft for detailed specification.

Common Specification

Board Thickness

0.004 to 0.24” (0.1–6.0 mm) *5
*compatibility for thickness exceeds 0.24” (6.0 mm) is optional
Monitor

Touch Screen LCD Monitor
Software

Windows 10 / Windows 11
Data Input Format

RS274X, RS274D, ODB++, DPF, DXF, BMP *6, TIFF *6

*5 When the vacuum table is used. Figures depend on the board warpage and clamp type. Printing quality may decrease with warpage. Please contact MicroCraft for more precise figures for specific conditions. *6 Scaling and alignment functions are not usable.

Vacuum Pump *

Power Supply

Three Phase AC200 V 10 A 50/60 Hz, AC220 V 10 A 60 Hz
Capacity

50 Hz: 20.7 ft³/min. (575 ℓ/min.)
60 Hz: 24.7 ft³/min. (685 ℓ/min.)
Air Coupler Size

RC 3/4
Weight

187.4lbs. (85 kg)

* Depends on clamping method

TOP